The Traeger grill differs from other grills in that it cooks food on a gas burner. The Traeger grill is a barbecue in which food is cooked on a gas burner. This grill will allow you to grill higher quality food with fewer fires and a more controlled cooking environment.
It can be frustrating when you think you’re cooking the perfect steak and your Traeger Pellet Grill suddenly displays an error message. You may start to wonder what went wrong and whether you are to blame. Follow this guide to learn about common Traeger grill errors and how to fix the commonly known LER code on Traeger grills.
What are Traeger Ler Error Codes?
This LEr code in the Traeger code stands for “low temperature error reading”, which is the reciprocal of HEr. The grill temperature dropped below 125 degrees F for more than ten minutes. Unless you are trying to cook slowly and slowly, you are unlikely to notice this error.
- The grill will turn off and you will have to restart it.
- Remove the briquettes from the kettle before proceeding with the start-up procedure.
Causes
There are several reasons why you might get a LER code on Traeger:
- The simplest explanation is that you have run out of pellets and have nothing to burn.
- The temperature of the outdoor grill may be so low that your Traeger cannot heat up.
- Debris can clog the fire pit and obstruct ventilation.
- Perhaps you have a bad batch of pellets filled with sawdust.
- The grill temperature controller may be faulty.
- If the ambient temperature is low, move the grill to a place protected from the wind or in direct sunlight to compensate.
- Consider purchasing an insulating blanket if you use your Traeger frequently in the winter.
- The last thing to double-check is the “p”setting. The letter “P”denotes the time between dumping pellets into the firebox from a drill.
- You can manually set this setting to one of three levels if you have an older Traeger.
What is Traeger Her Code Error Codes
If the temperature inside the grill exceeds 550F for more than 45 seconds, this will appear on the digital display. If this happens, your grill will turn off the auger and fan to begin the cooling process. When the temperature drops below 450 degrees Fahrenheit, the drill will work for 2 minutes to remove the embers from the auger tube.
- Turn off the grill and let it cool before removing the pellets from the pot.
- When you are ready to use the grill again, you will need to start it yourself.
- This is a bad sign and could mean the end of your meat if you don’t act quickly to control the temperature or remove it from the grill.
Causes
- A buildup of burning grease, ash, sawdust, or simply a faulty temperature sensor will give incorrect readings.
- Low grade pellets that burn unevenly are one of the main reasons for this temperature spike.
- In the worst case, your thermostat is broken.
- If you’ve ruled out all other possibilities and you’re still getting this error, it’s time to contact the manufacturer for help.
What are Traeger Error Codes? (Er1 and Er2)
This is a simple diagnosis, but it means you need to replace something. If this code appears, the RTD needs to be replaced.
RTD is short for “Resistance Temperature Detector”. It simply refers to the sensor probe. It measures the internal temperature of the grill.
Check the connection first to make sure it’s loose, but be prepared to order a replacement.
ER1
- This is a simple code related to the temperature sensor.
- All that has happened is that you have a faulty connection.
- Try pushing the plugin or uninstalling it entirely and reconnecting.
- If that doesn’t work, something may need to be tightened up, or there may be a faulty or broken part inside.
- Call Traeger to see if they can help you resolve the issue.
ER2
- This nasty error code on your Traeger indicates a short circuit inside the controller.
- This may be due to the RTD sensor or an internal connection.
- Contact Traeger support to resolve this issue.
Fix Traeger Ler Code Error Codes on Traeger Grills
- Fix LER Code on Traeger Pellet Grill
- Fix ERr Error Code on Traeger Grill
- Fix HER code on the Traeger grill
1. Correct the LER code on the Traeger pellet grill.
Here are some instructions for fixing the LER code on a Traeger grill.
- Use dehydrated, high quality wood pellets that do not crumble.
- Wood pellets from a previous boil must not be used.
- To remove ashes and sawdust from the firebox, always clean it.
- Ashes and sawdust should be removed from the furnace with a vacuum cleaner.
- Use an insulated cover for your Traeger in cold and windy weather.
- For a more regular supply of wood pellets to the auger in cold weather, you can optionally change the P setting from P-4 to P-3 or P-2.
- When cooking in the Traeger, be careful not to open the lid too often.
- Make sure the Traeger is properly started before lighting the wood pellets.
- Set Traeger to “Smoke”on traditional Traeger controllers (red panel) and leave the lid open as soon as smoke starts to come out, for 5-10 minutes.
- You can set any desired temperature and then close the lid.
- You don’t have to switch Traeger to smoke mode and keep the lid open when using a Pro Traeger controller like this.
- Keep the Traeger under the lid, setting the desired temperature.
- Follow this initial procedure when using a Traeger grill such as the Pro 34 to prevent LEr.
- Avoid pellet tunneling or voids in the Traeger hopper as these can reduce the amount of wood pellets available.
- To avoid tunneling or swirling of the pellets, keep stirring the wood pellets in the hopper every 30 minutes.
- The sound of the induction fan should be heard when the Traeger grill is turned on.
- Try manually spinning the fan to remove dirt if there is no sound, faint sound, or squeaky sounds. If the induction fan does not turn on, contact Traeger Customer Service.
- On the left side of the Traeger, check if the RTD temperature sensor is clean and pointing up. It must not touch the side of the Traeger grill.
2. Correct the ERr code on the Traeger grill.
Fix ERR or Er1 error
- Remove the two screws holding the temperature controller in place, leaving the Traeger unplugged.
- Loosen the screws holding the controller in place and carefully remove it.
- Make sure the two RTD wires are connected to the controller.
- If the wire connection is loose, cut some more wire from the loose wire, reinsert it, and tighten it again.
- Verify that the ERR issue is resolved. You can get a new temperature sensor from Traeger if the problem persists.
Fix ER2 bug
- The grill should be unplugged and allowed to cool slightly.
- Check for open wires after disconnecting the RTD sensor.
- Check the sensor wire connections in the green box of the controller case.
- Replace controller if ER2 code persists after probe replacement.
3. Fix HER Code on Traeger Grill
- If you have been cooking at temperatures above 300 or 350 degrees Fahrenheit for a long time, do not turn the Traeger knob to the off position.
- Before setting the knob to the off setting, turn the knob to a lower temperature of 225 degrees F for 5-10 minutes.
- Grease on the drip tray causes fire at high temperatures, which increases the temperature. Therefore, rinse the drip tray and put a new foil on it.
- It is not recommended to clog the auger or furnace with sawdust or ash.
- Make sure the temperature sensor is flawless and has a metallic sheen. There should be no traces of ash or smoke on it. The tip of the temperature probe only needs to be cleaned. You don’t need to turn it off.
- Raise the chimney cover to remove warm air from the Traeger. Maintain the height of the chimney cap between 2 and 3 inches.
- Replace temperature controller and sensor.
Other Common Traeger Grill Problems
When using a Traeger grill, you may encounter additional common problems. I will also provide you with more information about these issues. And offer details on how to solve these problems.
1. Puts out the fire on the Traeger grill
Traeger grills can burn for a variety of reasons. A hole in the grate is one of the main sources of ignition. We must track him down and stop him.
- The second important factor is the low quality of pellets purchased for grills.
- I think that you should always buy the best and most reliable pellets.
- Your electrical connection can be an important factor in a Traeger grill fire.
- Another factor is your grill fan, which can potentially put out a fire.
- This is due to a malfunction or stoppage of the grill fan.
2. Unusual temperature fluctuations
The cooking temperature you choose for Traeger grills is usually between 15 and 20 degrees Fahrenheit.
Take note of the grill temperature you have set for cooking. Raise the temperature to increase the frying time.
3. Fry on the Traeger without lighting
The auger of the Traeger grill turns and drops the pellets into the fireboxes, but the indicator of the grill device does not light up.
- This is the result of a malfunctioning igniter.
- Ideally, the grill should be fired without pellets.
- Remove the grill grates, drip tray and heat diffuser from the boiler.
- If the tip of the supplied igniter does not appear bright red to you, your grill is the problem.
4. There are no pellets in the kettle.
Pellets are ejected from the rotating top into the pot when the grill controller detects the system. This raises the temperature of the grill. This particular method, anchored in the grill, is fantastic and exhausting.
- Such a structure also takes some time to collapse.
- Pellets cannot enter the fire vessel when this system is out of order.
- It is responsible for lowering the grill temperature or slow cooking.
- You must also clean the auger tunnel. And after you separate the grill funnel and auger, you can do it.
Conclusion
The LEr error number indicates a low temperature problem and your Traeger grill has probably shut down. This occurs if the ambient temperature drops below 125°F after 10 minutes of grill operation. Follow all solutions to fix Ler code on Traeger grills.
In addition, I have discussed other common mistakes that can occur with a Traeger grill. I hope these fixes will help you solve any Traeger grill issue.
FAQ
How do I fix my Ler code on my Traeger?
Make sure your grill is clean and check the pot for dust as this could be the cause of your low temperature error code. There may be a problem with the temperature sensor. Restart it to see how it progresses. There may be issues with the p setting, also known as the “p”setting. You must do the same.
What does Ler mean on my Traeger?
A read with low error is called LEr. This notice will only appear on grills without WiFIRE, except for the 2017 Timberline 850 and 2017 Timberline 1300. This notification indicates that your grill has shut down because the temperature has dropped below 125°F for more than 10 minutes.
Why am I getting a low temperature error on my Traeger?
The best way to fix the low temperature error is to properly restart the grill. Grills with WiFIRE (or D2) support the demand to start with the lid closed. Thus, you must preheat the grill with the lid closed. If you don’t, your cook will most likely experience temperature fluctuations.
Why is my Traeger grill not heating up to the correct temperature?
Poor pellet quality is the most common cause of temperature problems. Always start troubleshooting if you are having temperature issues by removing and replacing the pellets and squeezing out any remaining sawdust from the hopper and auger tube.